The EDX-100A is a data recorder for measuring up to 256 channels.
Various conditioner cards are available for wide applications.
Specifications
|
Models
|
EDX-100A-4 (With DCS-100A)
EDX-100A-4-0
EDX-100A-4-1 (With DCS-100A and DCS-101A)
|
|
Max. Channels
|
32
|
|
Analog Input
|
Optional conditioner cards
Implement with DPM, CDV, CTA, CFV, CCA, CVM installed
|
|
CAN Data Input
|
Accepts one card of CAN-41A
|
|
Voice Memo Input
|
1 channel.
Record voice memos included with recordings alongside with measurement data (during manual measurements) using a dedicated remote control(optional accessory)
|
Sampling Frequency
|
Sampling Methods
|
Synchronous sampling of all channels
|
|
Sampling Frequency Series
|
1Hz to 100kHz(1-2-5 series): for 1 channel measurement
1Hz to 10kHz(1-2-5 series): for 16 channel measurement
1Hz to 5kHz(1-2-5 series): for 32 channel measurement
1Hz to 1kHz(1-2-5 series): for CAN data measurement
|
|
Data Storage
|
CF cards recommended by Kyowa
(128 MB to 8 GB; 45x speed or higher)
Up to 2 GB data for 1 time of measurement
|
|
Setting Conditions
|
Online: From the PC via LAN or USB port
Offline:
By reading from the CF card which has measuring conditions written with the DCS-100A data acquisition software
|
|
Saving Conditions
|
Amplifier setting conditions and measuring conditions are saved in the internal nonvolatile memory, enabling immediate setup with previous conditions upon power-on.
|
Measuring Modes
|
Manual
|
Data recording is manually started or stopped when data is recorded to a preset number of measured data.
Manual mode allows recording of voice memo during data recording.
|
|
Trigger
|
Data recording is automatically started when the preset trigger condition is satisfied.
Note that any CAN data mustn't be used as a trigger condition
|
|
Interval
|
Data recording is periodically made at preset intervals.
|
|
Manual Start/Stop of Data Recording
|
Possible by using the PC or by pressing the switch on the front panel or from the dedicated remote control unit
|
|
Balance Adjustment
|
Strain input channels are balanced by pressing the BAL. switch on the front panel or from the dedicated remote control unit or from the PC.
|
|
Saved Data Format
|
Kyowa standard format KS2, which enables data analysis with the optional Data Analysis Software DAS-200A
|
|
Collecting Data
|
LAN or USB port enables online data transfer to the PC, while CF card enables offline data transfer.
|
|
TEDS
|
Reads sensor's information and sets to channel condition automatically.
[Supported conditioner cards]
CDV-40B (-F)
DPM-42B (-F)
DPM-42B-I (-F)
CCA-40A (-F)
CDV-44AS
CDA-44AS/45AS
CVM-41A
AD-40AS (-F)
|
|
Synchronous Operation
|
Synchronous cable enables cascade connection of up to 8 units of the EDX-100A.
While data is recorded as a separate file in the CF card inserted into each unit, files of all cards are combined into a single file after online or offline data transfer to the PC.
|
|
Analog Output
|
All, except for CDV-40B (-F), AD-40AS (-F), and CAN-41A.
Conditioner cards provide an analog output connector, enabling voltage monitoring (±5 VFS).
|
|
CF Card Slot
|
1 (For data recording and condition setting)
|
Interfaces
|
|
LAN and USB (For control and data transfer), switchable
|
|
LAN I/F
|
10BASE-T/100BASE-TX
Connector: RJ45 modular jack
|
|
USB I/F
|
Conforms to USB 2.0 (High speed).
Connector: Series B receptacle
|
|
Operation Switches
|
REC/PAUSE: Starts/pauses data recording.
STOP: Stops data recording.
BAL.: Executes balance adjustment.
READ: Reads and sets conditions.
ID: Sets ID No. of EDX-100A.
LAN/USB: Switches communication port.
|
|
Indicators
|
Operation status indicator LEDs: 7
Channel status indicator LEDs:
The number corresponds to the number of channels provided.
|
|
External Control Connectors
|
CONT IN and CONT OUT
(For remote control and synchronous operation)
|
|
Operating Temperature
|
0 to 50ºC
|
|
Operating Humidity
|
20 to 90% (Non-condensing)
|
|
Storage Temperature
|
-20 to 60ºC
|
|
Vibration Resistant
|
±29.42 m/s2 (3 G), 5 to 55 Hz (When operating)
±49.03 m/s2 (5 G), 5 to 55 Hz (When not operating)
|
|
Impact Resistant
|
196.1 m/s2 (20 G) /11 ms
|
|
Power Supply
|
10 to 18 VDC
Connector: RM12BRD-4PH (Hirose)
DC power supply or optional dedicated AC adapter is required.
|
|
Current Consumption
|
Approx. 2.8 A
(When operated on 12 VDC with 4 CDV-40B cards mounted and full load applied)
|
|
Dimensions
|
137.5 W x 132.5 H x 255 D mm (Excluding protrusions)
|
|
Weight
|
2.0 kg
(2.6 kg with 4 CDV-40B card mounted)
|
|
Standard Accessories
|
DC power cable P-76
Ground wire P-72
USB cable N-38
CF card (1 GB)
DVD (Dynamic data acquisition software DCS-100A)
*DCS-100A is optional for models with suffix "-0".
|
|
Optional Accessories
|
USB cable N-39 (2 m)
Synchronous cable N-128
Camera synchronous cable N-98, N-99, N-101
AC adapter UIA345-12 (For U.S.A.: UNI345-1238)
Cable fixture
Synchronous extension unit ESYN-30A
Remote control unit RCU-41A
Battery unit for instantaneous power failure EDB-41B
Monitor unit EMON-20A
Dummy panel EDX2000-DUMMY
|
SANTA TECHNOLOGY CO.,LTD. (Head Office)
35/218 Moo. 2, Leabkhlongsam Rd., Khlongsam, Khlongluang, Pathumthani 12120
Call 02-101-3454 ,089-006-2766
Fax 02-101-3453
Mail. santatech@gmail.com
Line : @santatech
Web : https://santatechnology.com/
