Option Cards EDX-200A-2H/4H/4T

The ECAN-40A, ETIM-40A, and EGPC-40A are optional cards for EDX-200A. The cards can measure CAN data or GPS information without reducing the number of analog channels and sampling frequencies.

ECAN-40A
Multichannel CAN Card

Specifications

Applicable Models	EDX-200A-4H EDX-200A-2H (Installed in option slot) *For EDX-200A-4T, please use ECAN-40A M72.
CAN Ports	2 (High-speed CAN/low-speed CAN selectable)
Channels	Up to 512 (Total for 2 ports)
Compatible CAN Input Channels	CAN 2.0 A/B(Conforming to ISO-11898, ISO-11519-2)
Baud Rates	High speed CAN 1000, 800, 500, 250, 125, 100, 83.3, 62.5, 50, 33.3, 25, 20, and 10 [kbps] Low speed CAN 125, 100, 83.3, 62.5, 50, 33.3, 25, 20, and 10 [kbps]
CAN Data Output	Output at start: Output any given CAN data when AD conversion starts Output at stop: Output any given CAN data when AD conversion stops Manual output: Output any given CAN data at an arbitrary timing. Interval output: Output any given CAN data in a predetermined fixed cycle.

Digital I/O

I/O Points	Max. 8
I/O Settings	Switch among digital input, digital output and remote-controlled input for each bit (Common applied to all). *Remote control input: Start and stop measuring, execute BAL, etc.
Input Type	Isolated type, TTL level input
Input Voltage	Max. 5 VDC
Isolation Methods	Digital isolator
Output Type	Isolated type, open collector type output (With 10 kΩ internal pull-up resistors)
Output Voltage	5 VDC
Output Current	25 mA max. (Per point)
Isolation Methods	Digital isolator
Connector Type	CAN port: D-sub connector (Male) 9-pin Digital I/O port: MDR connector (Female) 14-pin

Operating Temperature	0 to 50°C, ECAN-40A M72 is -20 to 65°C
Operating Humidity	20 to 90% (Non-condensing)
Storage Temperature	-20 to 60°C, ECAN-40A M72 is -30 to 70°C
Dimensions	22.0 W x 128.0 H x 221.5 D mm
Weight	Approx. 170 g
Compliance	Directive 2014/30/EU (EMC) Directive 2011/65/EU, (EU)2015/863 (10 restricted substances) (RoHS)
	Note: When using EDX-200A and DCS-101A for arithmetic operation, no CAN measurement is possible.

Standard Accessories	Connector plug for digital I/O ports Shell case CANdb File Read Optional Software DCS-105A

ETIM-40A
Time Synchronization Card

Specifications

Applicable Models	EDX-200A-4H EDX-200A-2H (Installed in option slot) *For EDX-200A-4T, please use ETIM-40A M72.
Synchronization	Synchronizes the recording start time of remote EDX-200A units by using the time data received from GPS satellites.
GPS Data	Latitude, longitude, elevation, course over ground,speed, time, receiving conditions, the number of satellites in use, etc. Saving format: NMEA format

Digital I/O

I/O Points	Max. 8
I/O Settings	Switch among digital input, digital output and remote-controlled input for each bit (Common applied to all). *Remote control input: Start and stop measuring, execute BAL, etc.
Input Type	Isolated type, TTL level input
Input Voltage	Max. 5 VDC
Output Type	Isolated type, open collector type output (With 10 kΩ internal pull-up resistors)
Output Voltage	5 VDC
Output Current	25 mA max. (Per point)
Isolation Methods	Digital isolator
Connector Type	GPS sensor port: D-sub connector (Male) 9-pin Digital I/O port: MDR connector (Female) 14-pin

Operating Temperature	0 to 50°C ETIM-40A M72 is −20 to 65°C
Operating Humidity	20 to 90% (Non-condensing)
Storage Temperature	−20 to 60ºC ETIM-40A M72 is −30 to 70ºC
Dimensions	22.0 W x 128.0 H x 221.5 D mm
Weight	Approx. 160 g
Compliance	Directive 2014/30/EU (EMC) Directive 2011/65/EU, (EU)2015/863 (10 restricted substances) (RoHS)

Standard Accessories	Connector plug for digital I/O ports GPS sensor (Cable length: 5 m) Shell case

EGPC-40A
GPS/Multichannel CAN Card

Specifications

Applicable Models	EDX-200A-4H EDX-200A-2H (Installed in optional slot) *For EDX-200A-4T, please use EGPC-40A M72.
I/O Ports	GPS/CAN Shared Port 1 Dsub connector 9 pins (male) CAN only port 1 Dsub connector 9 pins (male) Digital I/O port 1 MDR connector 14 pins (female)
Channels	Up to 512
Compatible CAN Versions	CAN 2.0A/B (Conforming to ISO-11898, ISO-11519-2)
Baud Rates	High speed CAN: 1000, 800, 500, 250, 125, 100, 83.3, 62.5, 50, 33.3, 25, 20, and 10 [kbps] Low speed CAN: 125, 100, 83.3, 62.5, 50, 33.3, 25, 20, and 10 [kbps]
CAN Data Output	Output at start: Output any given CAN data when AD conversion starts Output at stop: Output any given CAN data when AD conversion stops Manual output: Output any given CAN data at an arbitrary timing. Interval output: Output any given CAN data in a predetermined fixed cycle.
GPS Data	Latitude, longitude, elevation, course over ground,speed, time, receiving conditions, the number of satellites in use, etc. Saving format: NMEA format
Synchronization	Synchronizes the recording start time of remote EDX-200A units by using the time data received from GPS satellites.

Digital I/O

I/O Points	Max. 8
I/O Settings	Switch among digital input, digital output and remote-controlled input for each bit (Common applied to all). *Remote-controlled input: Start and stop measuring, execute BAL, etc.
Input Type	Isolated type (Digital isolator), TTL level input
Input Voltage	Max. 5 VDC
Output Type	Isolated type (Digital isolator) Open collector type output (With 10 kΩ internal pull-up resistors)
Output Voltage	5 VDC
Output Current	25 mA max. (Per point)

Operating Temperature	0 to 50ºC EGPC-40A M72 is -20 to 65ºC
Operating Humidity	20 to 90% (Non-condensing)
Storage Temperature	-20 to 60ºC EGPC-40A M72 is -30 to 70ºC
Dimensions	22.0 W x 128.0 H x 221.5 D mm
Weight	Approx. 170 g
Compliance	Directive 2014/30/EU (EMC) Directive 2011/65/EU, (EU)2015/863 (10 restricted substances) (RoHS)
	When using EDX-200A and DCS-101A for arithmetic operation, no CAN measurement is possible.

Standard Accessories	Connector plug for digital I/O ports GPS sensor (Cable length: 5 m) Shell case CANdb File Read Optional Software DCS-105A

SANTA TECHNOLOGY CO.,LTD. (Head Office)
35/218 Moo. 2, Leabkhlongsam Rd., Khlongsam, Khlongluang, Pathumthani 12120
Call 02-101-3454 ,089-006-2766
Fax 02-101-3453
Mail. santatech@gmail.com
Line : @santatech
Web :  https://santatechnology.com/